Quantcast
Channel: PTC Community : Popular Discussions - Visualize
Viewing all 4806 articles
Browse latest View live
↧

How to get annotations displayed in Creo View's 'Viewables'

October 21, 2015, 4:41 am
$
0
0

Good morning to everybody,

 

perhaps someone of you have a solution for this problem:

 

I have defined some Combined States in a Creo assembly.

Some 3D annotations are assigned to specific combined states so that every state displays only certain annotations. This works fine in Creo Parametric 2 and 3.

 

I want these Combined states to be available under the "Viewables" Tab in Creo View (Lite).

 

I am using the RCP editor to configure the output of pvs/pvz files.

And in Creo I set the config option "intf_out_pvs_recipe_file" to the rcp file.

 

My problem:

When I export a PVS/PVZ file from Creo 2 (M180) the combined states are available in CreoView 3 (M031) as "Viewables", BUT annotations are shown in "Master View" only. The Combined States/Viewables doesn't show any annotations.

 

When I use  Creo 3 Parametric (M060) and the same rcp file for export to PVZ/PVS) then the notes/annotations are shown in CreoView 3 (M031). Creo 3 seems to use another option for this type of export.

 

My question:

Does anybody know if there is a config/rcp option for Creo 2 Parametric that ensures annotations to be displayed in CreoView Viewables? Our productive version is Croe 2 (and will be 2016), so Creo 3 isn't an option today.

 

Thanks in advance.

 

Andreas

↧
Search

Creo View opens pdf in Adobe Reader with error-message.

December 10, 2014, 2:58 am
$
0
0

Hi All

 

I am experiencing an issue with Creo View 1.0 Lite and hope you can help me find a solution.

 

When I click on a link to open a file from Windchill, the Internet Explorer starts Creo Viewer as expected.

But the Creo Viewer does not show the pdf-file.

The pdf-file is opened by Adobe Reader while Creo Viewer presents me with the error-message:

"Failed to load the file. Check the Adobe Acrobat or Adobe Reader Installation."

 

How do I configure Creo Viewer to show the pdf and not try to use Adobe Reader?

↧
↧

Underlying (invisible) parts become visible when saving as illustration from Creo Illustrate

December 12, 2016, 2:35 am
$
0
0

Hi,

 

When saving figures as illustration (SVG or CGM) from Creo Illustrate (3.1 and 4.0), I expect that the final SVG export is an identical representation of what is shown in the graphics area of Creo Illustrate. In my case however, certain paths (not all) of underlying parts become visible in the final SVG export while these are not visible in the Creo Illustrate graphics area.

 

I tried playing around with the different export options (Thick/Thin lines_Surface borders_Enhanced intersections, Segments_Polylines_Beziér paths, ...) but no difference. There are also no phantom parts in my model.

 

Does anyone have any suggestions please?

Thanks in advance.

 

CreoIllustrate_to_SVG_export.jpg

↧

What are .ol and .pvs files?

August 21, 2015, 1:47 am
$
0
0

Can anybody help me understand what are different file types in an unzipped pvz of a Creoview of an  Assembly? I have noticed -.pvs, xxx.ol and xxx.pvs files.

Screenshot attached below.

Thanks in advance.

↧

Using Creo View Express as a browser plugin

April 20, 2012, 6:36 am
$
0
0

Where can I find any documentation of how to configure and use the Creo View Express as a plugin in a webbrowser like Firefox.

 

So far I'm doing a

 

 

<embed height="100%" width="100%" name="plugin" src="nvidia-demo.pvz" type="application/x-pvlite9-ed">

 

 

It is displayed correctly but I want to disable the toolbar, for example.

Furthermore I need access to the JavaScript API to be able to communicate with the plugin.

 

I'm using Creo View Express, Version Creo 2.0, Datecode F000 build 23.

 

Thanks a lot for your help.

 

Thomas

↧
↧

How to download creo view toolkit

November 1, 2016, 6:01 am
$
0
0

Hello,

 

I am looking for creo view toolkit, Please share the link to download creo view toolkit setup.

 

Thanks,

Sudhakar

↧

Annoyance - Need help in preventing scroll bars when launching Creo View.

December 15, 2016, 4:50 am
$
0
0

Every time I launch Creo View 3.1 from Windchill 10.2 into an Internet Explorer 11 tab, I get the scrollbars to show up on the right and bottom panes.  To remove them, my workaround is to maximize the page and then minimize again.  Does anybody know the settings in Internet Explorer or Creo View to prevent this from happening?  The bottom scroll bar hides the information that I want to see or select!

 

 

scroll-bar_creo-view.JPG

↧

ProductView and Google Chrome

May 16, 2011, 1:12 pm
$
0
0

All,

 

I've been trying to get ProductView to work with the Google Chrome browser, but to no avail. ProductView works fine with IE and Firefox, and I've uninstalled and reinstalled multiple times to get the same results.

 

Does anyone know how to get google chrome to work with ProductView? It'd be nice to use a good/fast browser with Windchill, but ProductView is kind of necessary for me.

 

Also, as another side question - Firefox doesn't seem to want to find related items when placing parts in a workspace, Change Notice, etc. It just freezes while "processing". Anyone know how to fix this as well? This isn't as important if Google Chrome can be fixed.

↧
Search

ProductView 7.0 printing

June 17, 2008, 11:27 am
$
0
0
I have had a report where the printed drawing will have "font changes and some hidden lines become solid lines".

Arethere any solutions for this?

Regards,
Larry H. Smith
IT Engr Analyst



↧
↧

Creo View Enhancement Requests

February 26, 2014, 9:59 pm
$
0
0

Hi all,

 

I've a few enhancement ideas for Creo View, Here I'm listing below.

 

1 Creo View can't Measure the Radius/Diameters of Rounds. [Attaching an PPT]

2 Should be able to read the Cross-sections from Creo Parametric Files.

3 Should be able to read the Simplified Representations / Combined Views from Creo Parametric files.

4 Should be able to read the Views list from Creo Parametric Models.

 

These are the minimum requirements any Customer looks for.

 

Hope PTC implements the same.

 

Regards,

Niranjan V

↧

As stored drawings while everything else is latest?

December 21, 2016, 9:45 am
$
0
0

We are using "latest" for creating viewables within Windchill of EPDMdocuments.  Is there a way to have CREO drawings use "as stored" instead?  This is needed so that we have a static drawing of the changes.  We went to latest along with positioning and extended positioning assemblies so that we could update items for the manufacturing floor without redoing every assembly a part was used in.  We are on CREO 3, Windchill 10.2 m030 and CREO 3 m032 viz adapters.

↧

ProductView compatibility

August 12, 2009, 10:08 am
$
0
0
Does anybody know when ProductView will be able to view Wildfire 4.0 drawings?
↧

ProductView 9.1 M020 (Express, Lite, Professional) crashes

July 30, 2009, 1:14 am
$
0
0
ProductView 9.1 M020 (Express, Lite, Professional) crashes in Windows XP SP3 Czech Edition. Lite, Professional ... SW crashes immediatelly after launching. Express ... SW launches successfully, crash appears during Exit. In Windows XP SP3 English Edition, the SW works well. I appreciate any tip, how to solve the problem. Martin Hanak mhanak@cogras.cz mhanakptc@seznam.cz
↧
↧

License for ProductView 9.1

November 14, 2008, 12:53 am
$
0
0
Hi, Can anyone tell me how to obtain a ProductView 9.1 License as LM can't cut this and you cant run ProductView 9.1 professional on a 8.0 License. Kind Regards Paul Tanner
↧

ProductView and Pro/E on solaris 10

October 1, 2009, 5:57 am
$
0
0

I've installed productView and Pro/E on my Windchill server (solaris 10), however, whenI try to publish something it always errors out. It appears that I'm problems with Pro/E wanting the xserver process running in the background. Has anyone set this configuration up successfully? I've reviewed TPI 143625 and I am having difficulty setting up the virtual frame buffer decribed in the reference.

 

Thanks

↧
Search

Creo View printing black page

June 4, 2013, 8:38 am
$
0
0

Hi Everyone,

 

I'm having problems with some of our stations (mostly laptops with onboard intel graphics) which are working with Creo View 2.0. The program is able to open and view models and drawings but when the user selects print the image prints as a solid black page. This is repeatable accross all printers and even print to PDF converters. Has anyone seen this before and is there a known fix?

 

Thanks


Dave

↧

Creo View Enhancement Requests

February 26, 2014, 9:59 pm
$
0
0

Hi all,

 

I've a few enhancement ideas for Creo View, Here I'm listing below.

 

1 Creo View can't Measure the Radius/Diameters of Rounds. [Attaching an PPT]

2 Should be able to read the Cross-sections from Creo Parametric Files.

3 Should be able to read the Simplified Representations / Combined Views from Creo Parametric files.

4 Should be able to read the Views list from Creo Parametric Models.

 

These are the minimum requirements any Customer looks for.

 

Hope PTC implements the same.

 

Regards,

Niranjan V

↧
↧

Creo View opens pdf in Adobe Reader with error-message.

December 10, 2014, 2:58 am
$
0
0

Hi All

 

I am experiencing an issue with Creo View 1.0 Lite and hope you can help me find a solution.

 

When I click on a link to open a file from Windchill, the Internet Explorer starts Creo Viewer as expected.

But the Creo Viewer does not show the pdf-file.

The pdf-file is opened by Adobe Reader while Creo Viewer presents me with the error-message:

"Failed to load the file. Check the Adobe Acrobat or Adobe Reader Installation."

 

How do I configure Creo Viewer to show the pdf and not try to use Adobe Reader?

↧

vector illustration from creo view

October 8, 2012, 1:54 am
$
0
0

Hi everyone!!

 

I need your help. In my work usually need technical illustrations, this illustration come from creo, in vector files. But in the future i'll need obtain this 2D models from creo view. My problem is the export options in creo view. I try to export in PDF files, but the image is not a vector graphics. Really i don't now how to do, this program is new to me.

 

Thanks for your time, and sorry for my english level.

↧

Display Skeleton Geometry in Creo View

April 23, 2015, 8:31 am
$
0
0

I have a large assembly with several sub-assemblies. Each subassembly contains a skeleton model. Some of these skeleton models have geometry representing space claims. If I open any of the skeleton models by itself, the geometry is displayed. If I open an assembly containing the skeleton, the geometry is not displayed. How can I make the skeleton geometry display in the assembly?

 

 

↧
Viewing all 4806 articles
Browse latest View live
Search
<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>